某型发动机自反馈调节阀动态仿真分析

基于FLUENT软件提供的计算方法和物理模型，利用动网格技术及用户自定义函数（User-define Function，UDF），对发动机预燃室调节阀的自反馈调节过程进行动态数值模拟，并分析阻尼参数对调节效果的影响。结果表明：自反馈机构可实现对不同压力扰动的及时响应，具有稳定流量的效果，改变阻尼参数可对调节响应速度和流量稳定性进行优化，其中摩擦力对调节影响最显著。     

Magneto-rotation-fibre-reinforced thermoelastic with gravity and energy dissipation

In this article, two theories of the generalized thermoelasticity Green-Naghdi theory (of type II and III) are applied, as well as the coupled theory to study the effect of magnetic field and rotation under influence of gravity on 2D problem of a fibre-reinforced thermoelastic. The normal mode analysis is used to obtain the expressions for the temperature, displacement components and the thermal stresses distributions. The resulting formulation is applied for two different concrete problems. The first concerns the case of a punch moving across the surface of semi-infinite thermoelastic half-space subjected to appropriate boundary conditions. The second deals with a thick plate subjected to a time-dependent heat source on each face. Numerical results are illustrated graphically for each problem considered. A comparison is made with the results predicted obtained by the two theories in the presence and absence of magnetic field, rotation and gravity field.     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

不同发射率下红外热图像的非稳态温度场测量研究

通过分析红外测温公式,研究物体发射率对红外热图像测温精度的影响,并找出影响物体发射率的因素。根据经典计算方法,发现了物体发射率在红外热图像测温应用中的局限。从红外热图像的角度对发射率的计算进行了建模,基于修正物体发射率得到提高红外热图像对非稳态温度场测量精度的模型。对铸铁、不锈钢进行了3组测温实验,红外热图像直接测量的最大误差分别为2.1℃、1.7℃、2.3℃,而所提出的方法测量的最大误差分别为1.0℃、0.7℃、1.6℃。通过对比分析3组测量结果数据验证了测量方法的可行性。     

高供氧压力下高马赫数氧枪数值模拟

  以北方某钢厂100 t转炉为原型，建立顶吹转炉炉内流场的三维数学模型，采用Fluent软件研究了不同高马赫数氧气射流与熔池钢液速度流场分布之间的依赖关系。研究发现，高马赫数氧枪在Ma（马赫数）为2.0～2.3时，曲线平稳，为最佳供氧压力。在提高供氧压力的同时，氧气射流的最大速度、熔池钢液面的冲击直径及冲击深度也随之增加。模拟结果显示，氧气射流在设计工况氧压小于1.0 MPa时，射流之间相互干扰作用最弱；氧气射流在设计工况氧压力大于1.0 MPa后，冲击直径与冲击深度增幅较小。基于上述研究，在实际生产中应用了高马赫数氧枪后，并结合变枪变压操作工艺，可以改善熔池底部钢液流动状况、稳定转炉吹炼过程、控制炉渣喷溅。     

The residual zonal flow in tokamak plasmas with a poloidal electric field

In a tokamak plasma with auxiliary heating by cyclotron waves, a poloidal electric field will be produced, and as a consequence influence the residual zonal flow(RZF) level. The poloidal electric field can also be induced through biasing electrodes at the edge region of tokamaks.Numerical evaluation for a large aspect ratio circular cross section tokamak for the electron cyclotron wave heating indicates that the RZF level decreases significantly when the poloidal electric field increases. Qualitatively, the ion cyclotron wave heating is able to increase the RZF level. It is difficult to apply the calculation to the real cyclotron wave heating experiments since we need to know factors such as the plasma profiles, the exact power deposition and the cross section geometry, etc. It is possible to use the cyclotron wave heating to control the zonal flow and then to control the turbulence level in tokamak experiments.